MOLYMER MATEX is a general FRP manufacturing company.

Product Information

Hikarikabe size table

Internal dimension of the distance between foundation and beam

Use lower metal hardware
（Ｂ30-03）
Table1:3ｍｍ of lower gap
Range of internal dimension HIKARIKABE(H)
2962~2932 2916
2932~2902 2886
2902~2872 2856
2872~2842 2826
2842~2812 2796
2812~2782 2766
2782~2752 2736
2752~2722 2706
2722~2692 2676
2692~2662 2646
2662~2632 2616
2632~2602 2586
2602~2572 2556
2572~2542 2526
2542~2512 2496
2512~2482 2466
2482~2452 2436
2452~2422 2406
2422~2392 2376
2392~2362 2346
2362~2332 2316
2332~2302 2286
2302~2272 2256
Use lower metal hardware
（Ｂ30-12）
Table2:12ｍｍ of lower gap
Range of internal dimension HIKARIKABE(H)
2970~2940 2916
2940~2910 2886
2910~2880 2856
2880~2850 2826
2850~2820 2796
2820~2790 2766
2790~2760 2736
2760~2730 2706
2730~2700 2676
2700~2670 2646
2670~2640 2616
2640~2610 2586
2610~2580 2556
2580~2550 2526
2550~2520 2496
2520~2490 2466
2490~2460 2436
2460~2430 2406
2430~2400 2376
2400~2370 2346
2370~2340 2316
2340~2310 2286
2310~2280 2256
Use lower metal hardware
（Ｂ30-24）
Table3:24ｍｍ of lower gap
Range of internal dimension HIKARIKABE(H)
2982~2952 2916
2952~2922 2886
2922~2892 2856
2892~2862 2826
2862~2832 2796
2832~2802 2766
2802~2772 2736
2772~2742 2706
2742~2712 2676
2712~2682 2646
2682~2652 2616
2652~2622 2586
2622~2592 2556
2592~2562 2526
2562~2532 2496
2532~2502 2466
2502~2472 2436
2472~2442 2406
2442~2412 2376
2412~2382 2346
2382~2352 2316
2352~2322 2286
2322~2292 2256
Calculation example1

-Internal dimension 2600H/lower gap : 3mm

  1. 2602-2572 applies, which means that the size of Hikarikabe should be 2556mm (H).
Calculation example2

-Internal dimension 2700H/lower gap:12mm

  1. Refer to Table 2 and find the internal dimension section which 2700 applies to.
  2. It applies to both 2730-2700 and 2700-2670 so that you should choose either one to decide the size of Hikarikabe.
  3. If you choose 2730-2700, size of Hikarikabe would be 2676mm (H).

* Upper fixed metal hardware is suitable for both sizes since it has elongate hole.

Interdimension of pillar spacing

Table4:Correspondence table
Interdimension HIKARIKABE(W) Gap on one side Note
895 876 9.5
887.5 876 5.8 Only specification for metal support placed outside is usable
846 20.8
880 876 2.0 Only specification for metal support placed outside is usable
846 17.0
872.5 846 13.3
865 846 9.5
857.5 846 5.8 Only specification for metal support placed outside is usable
816 20.8
850 846 2.0 Only specification for metal support placed outside is usable
816 17.0
842.5 816 13.3
835 816 9.5
827.5 816 5.8 Only specification for metal support placed outside is usable
786 20.8
820 816 2.0 Only specification for metal support placed outside is usable
786 17.0
8125 786 13.3
805 786 9.5
797.5 786 5.8 Only specification for metal support placed outside is usable
756 20.8
790 786 2.0 Only specification for metal support placed outside is usable
756 17.0
782.5 756 13.3
775 756 9.5
767.5 756 5.8 Only specification for metal support placed outside is usable
726 20.8
760 756 2.0 Only specification for metal support placed outside is usable
726 17.0
752.5 726 13.3
745 726 9.5
737.5 726 5.8 Only specification for metal support placed outside is usable
730 726 2.0 Only specification for metal support placed outside is usable
Calculation example1

-Internal dimension: 805W
Refer to Table 4 and find the internal dimension section which 805 applies to.
Only 9.5mm of gap is capable so that the size of Hikarikabe would be 786mm (W).

 hikarikabe pict
Calculation example2

-Internal dimension: 790W

  1. Refer to Table4 and find the internal dimension section that 790 applies to.
  2. 2mm and 17mm of gaps are capable and choose either of them.
    (If there is no particular preference, we would recommend size which “Note” section is blank and both metal supports placed inside and outside are available: in case of Example 2, recommendation would be 17mm.)
  3. If 17mm of gap on one side is chose, size of Hikarikabe would be 756mm (W).
製品紹介

HIKARIKABE Specifications